TenGigabitEthernet¶

Keys

• name

Leafs

• channel_protocol
• cisco_ios_xe_ethernet_macsec
• cisco_ios_xe_switch_macsec
• delay
• description
• duplex
• if_state
• keepalive
• load_interval
• mac_address
• max_reserved_bandwidth
• media_type
• mtu
• nat66
• port_type
• service_insertion
• shutdown

Children

• access_session
• analysis_module
• arp
• authentication
• auto
• backup
• bandwidth
• bfd
• carrier_delay
• cdp
• cemoudp
• channel_group
• cisco_ios_xe_ethernet_macsec_option
• cisco_ios_xe_switch_macsec_option
• crypto
• cts
• cws_tunnel
• dampening
• datalink
• device_tracking
• domain
• dot1x
• dual_active
• eapol
• encapsulation
• energywise
• et_analytics
• ethernet
• evpn
• fabric_domain
• fair_queue
• fair_queue_conf
• flowcontrol
• hold_queue
• interface_qos
• ip
• ip_vrf
• ipv6
• isis
• keepalive_settings
• l2protocol_tunnel
• lacp
• lisp
• lldp
• load_balancing
• location
• logging
• mab
• mac
• macro
• mdix
• mka
• mop
• mpls
• mvrp
• negotiation
• ntp
• ospfv3
• peer
• performance
• plim
• pm_path
• power
• pppoe
• priority_queue
• rcv_queue
• service
• service_policy
• snmp
• source
• spanning_tree
• speed
• srr_queue
• stackwise_virtual
• standby
• storm_control
• switch
• switchport
• switchport_conf
• synchronous
• trust
• udld
• umbrella
• utd
• vlan_range
• vrf
• vrrp
• xconnect
• zone_member

Enum Classes

class Native.Interface.TenGigabitEthernet¶

Bases: Entity

Class Hierarchy : Native Interface TenGigabitEthernet

This class represents configuration data.

Ten Gigabit Ethernet

name(key)¶

type: str

media_type¶

Media type

type: MediaType

port_type¶

type: PortType

description¶

Interface specific description

type: str

pattern: .*

switchport_conf¶

type: SwitchportConf

switchport¶

Set switching mode characteristics

type: Switchport

stackwise_virtual¶

Configure stackwise-virtual link values

type: StackwiseVirtual

mac_address¶

Manually set interface MAC address

type: str

shutdown¶

Shutdown the selected interface

type: Empty

arp¶

Set arp type (arpa, probe, snap), timeout, log options or packet priority

type: Arp

backup¶

Modify backup parameters

type: Backup

cemoudp¶

cemoudp

type: Cemoudp

cws_tunnel¶

Configure Cloud Web Security Tunnel

type: CwsTunnel

l2protocol_tunnel¶

Tunnel Layer2 protocols

type: L2protocolTunnel

presence node: True

encapsulation¶

Set encapsulation type for an interface

type: Encapsulation

fair_queue_conf¶

type: FairQueueConf

fair_queue¶

Enable Fair Queuing on an Interface

type: FairQueue

flowcontrol¶

Configure flow operation

type: Flowcontrol

isis¶

IS-IS commands

type: Isis

keepalive¶

Enable keepalive

type: bool

keepalive_settings¶

type: KeepaliveSettings

bfd¶

BFD interface configuration commands

type: Bfd

bandwidth¶

Set bandwidth informational parameter

type: Bandwidth

dampening¶

Enable event dampening

type: Dampening

if_state¶

type: IfState

delay¶

Specify interface throughput delay

type: int

range: 1..16777215

domain¶

Specify a domain

type: Domain

hold_queue¶

Set hold queue depth

type: list of HoldQueue

mpls¶

type: Mpls

ip_vrf¶

type: IpVrf

vrf¶

VPN Routing/Forwarding parameters on the interface

type: Vrf

ip¶

Interface Internet Protocol config commands

type: Ip

ipv6¶

IPv6 interface subcommands

type: Ipv6

load_interval¶

Specify interval for load calculation for an interface

type: int

range: 0..600

logging¶

Configure logging for interface

type: Logging

mdix¶

Set Media Dependent Interface with Crossover

type: Mdix

mop¶

type: Mop

max_reserved_bandwidth¶

Maximum Reservable Bandwidth on an Interface

type: int

range: 1..100

mtu¶

Set the interface Maximum Transmission Unit (MTU)

type: int

range: 64..18000

interface_qos¶

type: InterfaceQos

service_insertion¶

Service-insertion AppNav Controller

type: ServiceInsertion

source¶

Get config from another source

type: Source

standby¶

HSRP interface configuration commands

type: Standby

access_session¶

Access Session specific Interface Configuration Commands

type: AccessSession

storm_control¶

storm configuration

type: StormControl

trust¶

Set trust value for the interface

type: Trust

priority_queue¶

Configure priority scheduling

type: PriorityQueue

rcv_queue¶

Configure receive queue(s)

type: RcvQueue

peer¶

Peer parameters for point to point interfaces

type: Peer

pm_path¶

Global pm-path configuration

type: PmPath

fabric_domain¶

Fabric-domain interface command

type: FabricDomain

lldp¶

LLDP interface subcommands

type: Lldp

service_policy¶

Configure QoS Service Policy

type: ServicePolicy

utd¶

UTD support on this interface

type: Utd

dot1x¶

Interface Config Commands for IEEE 802.1X

type: Dot1x

auto¶

Configure Automation

type: Auto

datalink¶

Interface Datalink commands

type: Datalink

energywise¶

EnergyWise interface configurations

type: Energywise

presence node: True

location¶

Interface location information

type: Location

mac¶

MAC interface commands

type: Mac

macro¶

Command macro

type: Macro

dual_active¶

type: DualActive

load_balancing¶

Etherchannel Load-Balancing

type: LoadBalancing

vlan_range¶

type: list of VlanRange

switch¶

type: Switch

srr_queue¶

type: SrrQueue

cisco_ios_xe_switch_macsec¶

Enable macsec on the interface

type: Empty

cisco_ios_xe_switch_macsec_option¶

Enable macsec on the interface

type: CiscoIOSXESwitchMacsecOption

device_tracking¶

Configure device-tracking on the interface

type: DeviceTracking

cts¶

Configure Cisco Trusted Security

type: Cts

power¶

type: Power

mka¶

MACsec Key Agreement (MKA) interface configuration

type: Mka

umbrella¶

Umbrella interface commands

type: Umbrella

snmp¶

Modify SNMP interface parameters

type: Snmp

performance¶

Global performance monitor configuration

type: Performance

carrier_delay¶

Specify delay for interface transitions

type: CarrierDelay

channel_group¶

Add this interface to an Etherchannel group

type: ChannelGroup

channel_protocol¶

Select the channel protocol (LACP, PAgP)

type: ChannelProtocol

ethernet¶

Ethernet interface parameters

type: Ethernet

eapol¶

eapol

type: Eapol

synchronous¶

Synchronous

type: Synchronous

speed¶

Configure speed operation

type: Speed

duplex¶

Configure duplex operation

type: Duplex

negotiation¶

Select autonegotiation mode

type: Negotiation

plim¶

Configure features on the PLIM

type: Plim

pppoe¶

pppoe interface subcommands

type: Pppoe

service¶

Configure Ether Service

type: Service

lacp¶

LACP interface subcommands

type: Lacp

cisco_ios_xe_ethernet_macsec¶

Enable macsec on the interface

type: Empty

cisco_ios_xe_ethernet_macsec_option¶

Enable macsec on the interface

type: CiscoIOSXEEthernetMacsecOption

xconnect¶

Xconnect commands

type: Xconnect

evpn¶

type: Evpn

mvrp¶

type: Mvrp

presence node: True

et_analytics¶

et-analytics support on this interface

type: EtAnalytics

lisp¶

Locator/ID Separation Protocol

type: Lisp

zone_member¶

Apply zone name

type: ZoneMember

crypto¶

Encryption/Decryption commands

type: Crypto

ospfv3¶

OSPFv3 interface commands

type: Ospfv3

udld¶

Configure UDLD enabled or disabled and ignore global UDLD setting

type: Udld

authentication¶

Auth Manager Interface Configuration Commands

type: Authentication

mab¶

type: Mab

presence node: True

nat66¶

NAT66 interface commands

type: Nat66

analysis_module¶

Configure NAM on the interface

type: AnalysisModule

vrrp¶

Configure VRRP

type: Vrrp

spanning_tree¶

Spanning Tree Subsystem

type: SpanningTree

ntp¶

Configure NTP

type: Ntp

cdp¶

CDP interface subcommands

type: Cdp