AtmInterfaceConfEntry

Keys

Leafs

Enum Classes

class ATMMIB.AtmInterfaceConfTable.AtmInterfaceConfEntry

Bases: Entity

Class Hierarchy : ATMMIB AtmInterfaceConfTable AtmInterfaceConfEntry

This class represents state data.

This list contains ATM interface configuration

parameters and state variables and is indexed

by ifIndex values of ATM interfaces.

ifindex(key)

type: int

range: 1..2147483647

refers to: ifindex

config: False

atminterfacemaxvpcs

The maximum number of VPCs (PVPCs and SVPCs) supported at this ATM interface. At the ATM UNI, the maximum number of VPCs (PVPCs and SVPCs) ranges from 0 to 256 only

type: int

range: 0..4096

config: False

atminterfacemaxvccs

The maximum number of VCCs (PVCCs and SVCCs) supported at this ATM interface

type: int

range: 0..65536

config: False

atminterfaceconfvpcs

The number of VPCs (PVPC, Soft PVPC and SVPC) currently in use at this ATM interface. It includes the number of PVPCs and Soft PVPCs that are configured at the interface, plus the number of SVPCs that are currently established at the interface. At the ATM UNI, the configured number of VPCs (PVPCs and SVPCs) can range from 0 to 256 only

type: int

range: 0..4096

config: False

atminterfaceconfvccs

The number of VCCs (PVCC, Soft PVCC and SVCC) currently in use at this ATM interface. It includes the number of PVCCs and Soft PVCCs that are configured at the interface, plus the number of SVCCs that are currently established at the interface

type: int

range: 0..65536

config: False

atminterfacemaxactivevpibits

The maximum number of active VPI bits configured for use at the ATM interface. At the ATM UNI, the maximum number of active VPI bits configured for use ranges from 0 to 8 only

type: int

range: 0..12

config: False

atminterfacemaxactivevcibits

The maximum number of active VCI bits configured for use at this ATM interface

type: int

range: 0..16

config: False

atminterfaceilmivpi

The VPI value of the VCC supporting the ILMI at this ATM interface. If the values of atmInterfaceIlmiVpi and atmInterfaceIlmiVci are both equal to zero then the ILMI is not supported at this ATM interface

type: int

range: 0..4095

config: False

atminterfaceilmivci

The VCI value of the VCC supporting the ILMI at this ATM interface. If the values of atmInterfaceIlmiVpi and atmInterfaceIlmiVci are both equal to zero then the ILMI is not supported at this ATM interface

type: int

range: 0..65535

config: False

atminterfaceaddresstype

The type of primary ATM address configured for use at this ATM interface

type: AtmInterfaceAddressType

config: False

status: deprecated

atminterfaceadminaddress

The primary address assigned for administrative purposes, for example, an address associated with the service provider side of a public network UNI (thus, the value of this address corresponds with the value of ifPhysAddress at the host side). If this interface has no assigned administrative address, or when the address used for administrative purposes is the same as that used for ifPhysAddress, then this is an octet string of zero length

type: str

config: False

status: deprecated

atminterfacemyneighboripaddress

The IP address of the neighbor system connected to the far end of this interface, to which a Network Management Station can send SNMP messages, as IP datagrams sent to UDP port 161, in order to access network management information concerning the operation of that system. Note that the value of this object may be obtained in different ways, e.g., by manual configuration, or through ILMI interaction with the neighbor system

type: str

pattern: (([0-9]|[1-9][0-9]|1[0-9][0-9]|2[0-4][0-9]|25[0-5])\.){3}([0-9]|[1-9][0-9]|1[0-9][0-9]|2[0-4][0-9]|25[0-5])(%[\p{N}\p{L}]+)?

config: False

atminterfacemyneighborifname

The textual name of the interface on the neighbor system on the far end of this interface, and to which this interface connects. If the neighbor system is manageable through SNMP and supports the object ifName, the value of this object must be identical with that of ifName for the ifEntry of the lowest level physical interface for this port. If this interface does not have a textual name, the value of this object is a zero length string. Note that the value of this object may be obtained in different ways, e.g., by manual configuration, or through ILMI interaction with the neighbor system

type: str

config: False

atminterfacecurrentmaxvpibits

The maximum number of VPI Bits that may currently be used at this ATM interface. The value is the minimum of atmInterfaceMaxActiveVpiBits, and the atmInterfaceMaxActiveVpiBits of the interface’s UNI/NNI peer. If the interface does not negotiate with its peer to determine the number of VPI Bits that can be used on the interface, then the value of this object must equal atmInterfaceMaxActiveVpiBits

type: int

range: 0..12

config: False

atminterfacecurrentmaxvcibits

The maximum number of VCI Bits that may currently be used at this ATM interface. The value is the minimum of atmInterfaceMaxActiveVciBits, and the atmInterfaceMaxActiveVciBits of the interface’s UNI/NNI peer. If the interface does not negotiate with its peer to determine the number of VCI Bits that can be used on the interface, then the value of this object must equal atmInterfaceMaxActiveVciBits

type: int

range: 0..16

config: False

atminterfacesubscraddress

The identifier assigned by a service provider to the network side of a public network UNI. If this interface has no assigned service provider address, or for other interfaces this is an octet string of zero length

type: str

config: False

atmintfpvcfailures

The number of times the operational status of a PVCL on this interface has gone down

type: int

range: 0..4294967295

config: False

atmintfcurrentlyfailingpvcls

The current number of VCLs on this interface for which there is an active row in the atmVclTable having an atmVclConnKind value of `pvc’ and an atmVclOperStatus with a value other than `up’

type: int

range: 0..4294967295

config: False

atmintfpvcfailurestrapenable

Allows the generation of traps in response to PVCL failures on this interface

type: bool

config: False

atmintfpvcnotificationinterval

The minimum interval between the sending of cIntfPvcFailuresTrap notifications for this interface

type: int

range: 1..3600

config: False

units: seconds

atmpreviouslyfailedpvclinterval

The interval for storing the failed time in atmPreviouslyFailedPVclTimeStamp

type: int

range: 0..3600

config: False

units: seconds

catmintfcurrentlydowntouppvcls

The current number PVCLs on this interface which changed state to ‘up’ since the last atmIntPvcUp2Trap was sent

type: int

range: 0..4294967295

config: False

catmintfoamfailedpvcls

The total number of PVCLs in this interface which are currently in the OAM loopback failed condition but the status of each PVCL remain in the ‘up’ state

type: int

range: 0..4294967295

config: False

catmintfcurrentoamfailingpvcls

The current number of PVCLs on this interface for which the OAM loop back has failed but the status of each PVCL remain in the ‘up’ state in the last notification interval

type: int

range: 0..4294967295

config: False

catmintfsegccoamfailedpvcls

The total number of PVCLs in this interface which are currently in the Segment CC OAM failed condition but the status of each PVCL remain in the ‘up’ state

type: int

range: 0..4294967295

config: False

catmintfcursegccoamfailingpvcls

The current number of PVCLs on this interface for which the Segment CC OAM has failed but the status of each PVCL remain in the ‘up’ state in the last notification interval

type: int

range: 0..4294967295

config: False

catmintfendccoamfailedpvcls

The total number of PVCLs in this interface which are currently in the End-to-End CC OAM failed condition but the status of each PVCL remain in the ‘up’ state

type: int

range: 0..4294967295

config: False

catmintfcurendccoamfailingpvcls

The current number of PVCLs on this interface for which the End-to-End CC OAM has failed but the status of each PVCL remain in the ‘up’ state in the last notification interval

type: int

range: 0..4294967295

config: False

catmintfaisrdioamfailedpvcls

The total number of PVCLs in this interface which are currently in the AIS RDI OAM failed condition but the status of each PVCL remain in the ‘up’ state

type: int

range: 0..4294967295

config: False

catmintfcuraisrdioamfailingpvcls

The current number of PVCLs on this interface for which the AIS RDI OAM has failed but the status of each PVCL remain in the ‘up’ state in the last notification interval

type: int

range: 0..4294967295

config: False

catmintfanyoamfailedpvcls

The total number of PVCLs in this interface which are currently in any type of OAM failed condition but the status of each PVCL remain in the ‘up’ state

type: int

range: 0..4294967295

config: False

catmintfcuranyoamfailingpvcls

The current number of PVCLs on this interface for which any of OAM has failed but the status of each PVCL remain in the ‘up’ state in the last notification interval

type: int

range: 0..4294967295

config: False

catmintftypeofoamfailure

Type of OAM failure

type: CatmOAMFailureType

config: False

catmintfoamrcovedpvcls

The total number of PVCLs in this interface which are currently in the OAM loopback recovered condition and the status of each PVCL is in the ‘up’ state

type: int

range: 0..4294967295

config: False

catmintfcurrentoamrcovingpvcls

The current number of PVCLs on this interface for which the OAM loop back has recovered and the status of each PVCL is in the ‘up’ state in the last notification interval

type: int

range: 0..4294967295

config: False

catmintfsegccoamrcovedpvcls

The total number of PVCLs in this interface which are currently in the Segment CC OAM recovered condition and the status of each PVCL is in the ‘up’ state

type: int

range: 0..4294967295

config: False

catmintfcursegccoamrcovingpvcls

The current number of PVCLs on this interface for which the Segment CC OAM has recovered and the status of each PVCL is in the ‘up’ state in the last notification interval

type: int

range: 0..4294967295

config: False

catmintfendccoamrcovedpvcls

The total number of PVCLs in this interface which are currently in the End-to-End CC OAM recovered condition and the status of each PVCL is in the ‘up’ state

type: int

range: 0..4294967295

config: False

catmintfcurendccoamrcovingpvcls

The current number of PVCLs on this interface for which the End-to-End CC OAM has recovered and the status of each PVCL is in the ‘up’ state in the last notification interval

type: int

range: 0..4294967295

config: False

catmintfaisrdioamrcovedpvcls

The total number of PVCLs in this interface which are currently in the AIS RDI OAM recovered condition and the status of each PVCL is in the ‘up’ state

type: int

range: 0..4294967295

config: False

catmintfcuraisrdioamrcovingpvcls

The current number of PVCLs on this interface for which the AIS RDI OAM has recovered and the status of each PVCL is in the ‘up’ state in the last notification interval

type: int

range: 0..4294967295

config: False

catmintfanyoamrcovedpvcls

The total number of PVCLs in this interface which are currently in any type of OAM recovered condition and the status of each PVCL is in the ‘up’ state

type: int

range: 0..4294967295

config: False

catmintfcuranyoamrcovingpvcls

The current number of PVCLs on this interface for which any of OAM has recovered and the status of each PVCL is in the ‘up’ state in the last notification interval

type: int

range: 0..4294967295

config: False

catmintftypeofoamrecover

Type of OAM Recovered

type: CatmOAMRecoveryType

config: False

atmintfcurrentlydowntouppvcls

The current number PVCLs on this interface which changed state to ‘up’ since the last atmIntPvcUpTrap was sent

type: int

range: 0..4294967295

config: False

atmintfoamfailedpvcls

The total number of PVCLs in this interface which are currently in the oam loopback failed condition but the status of each PVCL remain in the ‘up’ state

type: int

range: 0..4294967295

config: False

atmintfcurrentlyoamfailingpvcls

The current number of PVCLs on this interface for which the oam loop back has failed but the status of each PVCL remain in the ‘up’ state in the last notification interval

type: int

range: 0..4294967295

config: False