IfOperStatusReason

class ydk.models.cisco_ios_xe.CISCO_TC.IfOperStatusReason

IfOperStatusReason (Enum Class)

The cause of current operational state of the

interface.

GLOSSARY:

BB - Buffer-to-Buffer.

BB_Credit - Buffer-to-Buffer credit, a link level flow

control mechanism.

B_Port - A Fibre Channel, Bridging port.

BPDU - Bridge Protocol Data Unit.

CDP - Cisco Discovery Protocol.

Class F - A connectionless service with notification on

non-delivery between E_Ports, used for control,

coordination, and configuration of the Fabric.

Class N - Refers to any class of service (different types

of frame delivery services) other than Class F.

E_D_TOV - Error Detect Timeout Value.

ENM - Egress Non-Multicast.

ELP - Exchange Link Parameter.

E-mode - A fibre channel port providing E_Port

functionality.

E_Port - A Fabric Expansion Port.

EPP - Exchange Peer Parameters.

ESC - Exchange Switch Capabilities.

Fabric - The set of physically connected fibre channel

switches.

FEX - Fabric EXtender.

FC-FS - Fibre Channel Framing and Signaling.

FCIP - Fibre Channel over IP protocol.

FCID - Fibre Channel Domain ID.

FCOE - Fibre Channel Over Ethernet.

FCOT - Fibre channel optical transmitter.

FC-PH - The Fibre Channel Physical and Signaling

standard.

FCSP - Fibre Channel Security Protocol.

Fibre Channel - The primary protocol for building SANs.

FICON - An I\O protocol used between IBM (and compatible)

mainframes and storage.

FLOGI - Fabric Login, used by a node port to establish a

session with the fabric.

GBIC - Gigabit Interface Converter; a removable

transceiver module permitting Fibre Channel and

Gigabit Ethernet physical-layer transport.

Interconnect_Ports - Switch Ports that assume either the

E_Port or B_Port mode are generally referred to

as Interconnect_Ports.

LACP - Link Access Control Protocol.

LIP - Loop Initialization Primitive sequence.

LR - Link Reset, the FC-PH defined primitive sequence

used to initiate a link reset.

MTU - Maximun transmission unit.

NOS - Not Operational Sequence, the FC-PH defined

primitive sequence to indicate that the

transmitting port has detected a link failure (or)

offline condition.

VIC - Virtual Interface Card.

VPC - Virtual Port Channel.

NPIV - N Port Identifier Virtualization.

NPV - NPort Virtualizer.

Nx_Port - A Fiber Channel Node Port.

OLS - Offline Sequence, the FC-PH defined primitive

sequence to indicate that the port is entering

into offline state.

OHMS - Online Health Management System.

PMON - Port Monitor.

R_A_TOV - Resource Allocation Timeout Value.

RCF - Reconfigure Fabric.

Rxbbcredit - Receive BB credit value configured for

a FC interface.

SAN - Storage Area Network; a network linking computing

devices to disk or tape arrays and other devices

over Fibre Channel.

SIF - Service Information Field.

SDM - Security Device Manager.

SDP - Secure Device Provisioning.

SFP - Small Formfactor Pluggable.

TE_Port - Trunking E_Port.

TOV - Time out value.

UDLD - Uni Directional Link Detection.

VDC - Virtual Device Context.

VEM - Virtual Ethernet Module.

VFC - Virtual Fibre Channel.

VRF - VPN Routing and Forwarding.

VSAN - Virtual Storage Area Network.

WWN - World Wide Name.

xE_Port - A Fiber channel port that can assume either

E_Port or TE_Port mode.

The enumerated values which provides the cause of the current

operational state of the interface are,

‘other(1)’ - reasons other than defined here.

‘none(2)’ - no failure.

‘hwFailure(3)’ - hardware failure.

‘loopbackDiagFailure(4)’ - loopback diagnostics failure.

‘errorDisabled(5)’ - the port is not operational due to

some error conditions that require administrative

attention.

‘swFailure(6)’ - software failure.

‘linkFailure(7)’ - physical link failure.

‘offline(8)’ - physical link is in offline state as

defined in the FC-FS standards.

‘nonParticipating(9)’ - during loop initialization, the

port is not allowed to participate in loop operations.

‘initializing(10)’ - port is being initialized.

‘vsanInactive(11)’- port VSAN is inactive. The port becomes

operational again when the port VSAN is active.

‘adminDown(12)’ - ifAdminStatus is ‘down’.

‘channelAdminDown(13)’ - this port is a member of a port

channel and that port channel’s ifAdminStatus is

‘down’.

‘channelOperSuspended(14)’ - this port is a member of a

port channel and its operational parameters are

incompatible with the port channel parameters.

‘channelConfigurationInProgress(15)’ - this port is

undergoing a port channel configuration.

‘rcfInProgress(16)’ - an isolated xE_port is transmitting

an reconfigure fabric, requesting a disruptive

reconfiguration in an attempt to build a single,

non-isolated fabric. Only the Interconnect_Ports can

become isolated.

‘elpFailureIsolation(17)’ - during a port initialization

the prospective Interconnect_Ports find incompatible

link parameters.

‘escFailureIsolation(18) - during a port initialization the

prospective Interconnect_Ports are unable to proceed

with initialization as a result of ESC.

‘domainOverlapIsolation(19)’ - there is a overlap in

domains while attempting to connect two existing

fabrics.

‘domainAddrAssignFailureIsolation(20)’ - the elected

principal switch is not capable of performing domain

address manager functions so no Nx_port traffic can be

forwarded across switches, hence all Interconnect_Ports

in the switch are isolated.

‘domainOtherSideEportIsolation(21)’ - the peer E_port is

isolated.

‘domainInvalidRcfReceived(22)’ - invalid RCF received.

‘domainManagerDisabled(23) - domain manager is disabled.

‘zoneMergeFailureIsolation(24)’ - the two Interconnect_Ports

cannot merge zoning configuration after having exchanged

merging request for zoning.

‘vsanMismatchIsolation(25)’ - this VSAN is not configured

on both sides of a trunk port.

‘parentDown(26)’ - the physical port to which this interface

is bound is down.

‘srcPortNotBound(27)’- no source port is specified for this

interface.

‘interfaceRemoved(28)’ - interface is being removed.

‘fcotNotPresent(29)’ - FCOT (GBIC) not present.

‘fcotVendorNotSupported(30)’ - FCOT (GBIC) vendor is not

supported.

‘incompatibleAdminMode(31)’ - port administrative mode is

incompatible with port capabilities.

‘incompatibleAdminSpeed(32)’ - port speed is incompatible

with port capabilities.

‘suspendedByMode(33)’ - port that belongs to a port channel

is suspended due to incompatible operational mode.

‘suspendedBySpeed(34)’ - port that belongs to a port channel

is suspended due to incompatible operational speed.

‘suspendedByWwn(35)’ - port that belongs to a port channel

is suspended due to incompatible remote switch WWN.

‘domainMaxReTxFailure(36)’ - domain manager failure after

maximum retries.

‘eppFailure(37)’ - trunk negotiation protocol failure after

maximum retries.

‘portVsanMismatchIsolation(38)’ - an attempt is made to

connect two switches using non-trunking ports having

different port VSANs.

‘loopbackIsolation(39)’ - port is connected to another port

in the same switch.

‘upgradeInProgress(40)’ - linecard upgrade in progress.

‘incompatibleAdminRxBbCredit(41)’ - receive BB credit is

incompatible.

‘incompatibleAdminRxBufferSize(42)’ - receive buffer size

is incompatible.

‘portChannelMembersDown(43)’ - no operational members.

‘zoneRemoteNoRespIsolation(44)’ - isolation due to remote

zone server not responding.

‘firstPortUpAsEport(45)’ - in a over subscribed line card,

when the first port in a group is up in E-mode, other

ports in that group cannot be brought up.

‘firstPortNotUp(46)’ - in a over subscribed line card,

first port cannot be brought up in E-mode when the

other ports in the group are up.

‘peerFcipPortClosedConnection(47)’ - port went down because

peer FCIP port closed TCP connection.

‘peerFcipPortResetConnection(48)’ - port went down because

the TCP connection was reset by the peer FCIP port.

‘fcipPortMaxReTx(49)’ - FCIP port went down due to maximum

TCP re-transmissions reached the configured limit.

‘fcipPortKeepAliveTimerExpire(50)’ - FCIP port went down

due to TCP keep alive timer expired.

‘fcipPortPersistTimerExpire(51)’ - FCIP port went down due

to TCP persist timer expired.

‘fcipPortSrcLinkDown(52)’ - FCIP port went down due to

Ethernet link down.

‘fcipPortSrcAdminDown(53)’ - FCIP port went down because

the source Ethernet link was administratively shutdown.

‘fcipPortAdminCfgChange(54)’ - FCIP port went down due to

configuration change.

‘fcipSrcPortRemoved(55)’ - FCIP port went down due to source

port removal.

‘fcipSrcModuleNotOnline(56)’ - FCIP port went down due to

source module not online.

‘invalidConfig(57)’ - this port has a misconfiguration with

respect to port channels.

‘portBindFailure(58)’ - port got isolated due to port bind

failure.

‘portFabricBindFailure(59)’ - port got isolated due to

fabric bind failure.

‘noCommonVsanIsolation(60)’ - trunk is isolated because

there are no common VSANs with peer.

‘ficonVsanDown (61)’ - FICON VSAN down.

‘invalidAttachment (62)’ - invalid attachment.

‘portBlocked (63)’ - port blocked due to FICON.

‘incomAdminRxBbCreditPerBuf (64)’ - disabled due to

incompatible administrative port rxbbcredit,

performance buffers.

‘tooManyInvalidFlogis (65)’ - suspended due to too many

invalid FLOGIs.

‘deniedDueToPortBinding (66)’ - suspended due to port

binding.

‘elpFailureRevMismatch (67)’ - isolated for ELP failure due

to revision mismatch.

‘elpFailureClassFParamErr (68)’ - isolated for ELP failure

due to Class F parameter error.

‘elpFailureClassNParamErr (69)’ - isolated for ELP failure

due to Class N parameter error.

‘elpFailureUnknownFlowCtlCode (70)’ - isolated for ELP

failure due to invalid flow control code.

‘elpFailureInvalidFlowCtlParam (71)’ - isolated for ELP

failure due to invalid flow control parameter.

‘elpFailureInvalidPortName(72)’ - isolated for ELP failure

due to invalid port name.

‘elpFailureInvalidSwitchName (73)’ - isolated for ELP

failure due to invalid switch name.

‘elpFailureRatovEdtovMismatch (74)’ - isolated for ELP

failure due to R_A_TOV or E_D_TOV mismatch.

‘elpFailureLoopbackDetected (75)’ - isolated for ELP

failure due to loopback detected.

‘elpFailureInvalidTxBbCredit (76)’ - isolated for ELP

failure due to invalid transmit BB credit.

‘elpFailureInvalidPayloadSize (77)’ - isolated for ELP

failure due to invalid payload size.

‘bundleMisCfg (78)’ - misconfiguration in port channel

membership detected.

‘bitErrRuntimeThreshExceeded (79)’ - bit error rate too

high. It has exceeded the run time threshold.

‘linkFailLinkReset (80)’ - link failure due to link reset.

‘linkFailPortInitFail (81)’ - link failure due to port

initialization failure.

‘linkFailPortUnusable (82)’ - link failure due to port

unusable.

‘linkFailLossOfSignal (83)’ - link failure due to loss of

signal.

‘linkFailLossOfSync (84)’ - link failure due to loss of

sync.

‘linkFailNosRcvd (85)’ - link failure due to non-operational

sequences received.

‘linkFailOLSRcvd (86)’ - link failure due to offline

sequences received.

‘linkFailDebounceTimeout (87)’ - link failure due to

re-negotiation failed.

‘linkFailLrRcvd (88)’ - link failure when link reset(LR)

operation fails due to non-empty receive queue.

‘linkFailCreditLoss (89)’ - link failure due to excessive

credit loss indications.

‘linkFailRxQOverflow (90)’ - link failure due to receive

queue overflow.

‘linkFailTooManyInterrupts (91)’ - link failure due to

excessive port interrupts.

‘linkFailLipRcvdBb (92)’ - link failure when loop

initialization(LIP) operation fails due to non empty

receive queue.

‘linkFailBbCreditLoss (93)’ - link failure when link

reset(LR) operation fails due to queue not empty.

‘linkFailOpenPrimSignalTimeout (94)’ - link failure due to

open primitive signal timeout while receive queue

not empty.

‘linkFailOpenPrimSignalReturned (95)’ - link failure due to

open primitive signal returned while receive queue

not empty.

‘linkFailLipF8Rcvd (96)’ - link failure due to F8 LIP

received.

‘linkFailLineCardPortShutdown (97)’ - link failure due to

port shutdown.

‘fcspAuthenFailure (98)’ - fibre channel security protocol

authorization fail.

‘fcotChecksumError (99)’ - FCOT SPROM checksum error.

‘ohmsExtLoopbackTest (100)’ - link suspended due to external

loopback diagnostics failure.

‘invalidFabricBindExchange (101)’ - invalid fabric binding

exchange.

‘tovMismatch (102)’ - link isolation due to TOV mismatch.

‘ficonNotEnabled (103)’ - FICON not enabled.

‘ficonNoPortNumber (104)’ - no FICON port number.

‘ficonBeingEnabled (105)’ - FICON is being enabled.

‘ePortProhibited (106)’ - port down because FICON prohibit

mask in place for E/TE port.

‘portGracefulShutdown (107)’ - port has been shutdown

gracefully.

‘trunkNotFullyActive (108)’ - some of the VSANs which are

common with the peer are not up.

‘fabricBindingSwitchWwnNotFound (109)’ - peer switch WWN not

found in fabric binding active database.

‘fabricBindingDomainInvalid (110)’ - peer domain ID is

invalid in fabric binding active database.

‘fabricBindingDbMismatch (111)’ - fabric binding active

database mismatch with peer.

‘fabricBindingNoRspFromPeer (112)’ - fabric binding no

response from peer.

‘dpvmVsanSuspended (113)’ - dpvm vsan is suspended.

‘dpvmVsanNotFound (114)’ - dpvm vsan not found.

‘trackedPortDown (115)’ - port down because tracked

port is down.

‘ecSuspendedOnLoop (116)’ - port suspended because extended

BB credits are configured on loop port.

‘isolateBundleMisCfg (117)’ - port isolated due to bundle

mis-configuration.

‘noPeerBundleSupport (118)’ - peer port does not support

bundle.

‘portBringupIsolation (119)’ - trunk port isolated during

bringup time.

‘domainNotAllowedIsolated (120)’ - port isolated due to

domain not allowed.

‘virtualIvrDomainOverlapIsolation (121)’ - port isolated

due to virtual IVR domain overlap.

‘outOfService (122)’ - port is in out of service state.

‘portAuthFailed (123)’ - port has encountered an 802.1x

authentication failure.

‘bundleStandby (124)’ - port cannot be brought up in

a bundle, since the bundle has max members.

‘portConnectorTypeErr (125)’ - Error in the port connector

type (SFP).

‘errorDisabledReInitLmtReached (126)’ - the port is not

operational after trying to initialize the port multiple

times due to some erorrs.

‘ficonDupPortNum (127)’ - the ficon vsan has a duplicate

port number.

‘localRcf (128)’ - fcdomain applied a locally disruptive

reconfiguration (the local domain became invalid; no

RCF frames have been sent outside the local switch).

‘twoSwitchesWithSameWWN (129)’ - merge attempt between

VSANs containing the same WWN. If the user attempts to

merge two different VSANs and both have at least one

switch with the same WWN then the link in between the

VSANs is isolated.

‘invalidOtherSidePrincEFPReqRecd (130)’ - EFP request frame

indicating a principal switch other than the locally

known one.

‘domainOther (131)’ - other domain manager reasons not

defined here.

‘elpFailureAllZeroPeerWWNRcvd (132)’ - isolated for ELP

failure due to peer WWN is received with all zeros.

‘preferredPathIsolation (133)’ - port isolated due to

preferred path not able to program the routes.

‘fcRedirectIsolation (134)’ - port isolated due to

FC Redirect not being able to program routes.

‘portActLicenseNotAvailable (135)’ - port not brought up

due to lack of port activation licenses.

‘sdmIsolation (136)’ - port isolated due to SDM

(Security Device Manager) not being

able to program routes.

‘fcidAllocationFailed (137)’ - port down due to failure

in FCID (Fibre Channel Domain ID) allocation.

‘externallyDisabled (138)’ - port externally disabled.

‘unavailableNPVUpstreamPort (139)’ - NPV

(NPort Virtualizer) upstream port not available.

‘unavailableNPVPrefUpstreamPort (140)’ - NPV

(NPort Virtualizer) preferred

upstream port not available.

‘sfpReadError (141)’ - the port is not operational due to

SFP (Small Formfactor Pluggable) read error.

‘stickyDownOnLinkFailure (142)’ - the port is

not operational due to link failure

in the sticky down mode.

‘tooManyLinkFlapsErr (143)’ - too many link flaps

on the port in a short interval.

‘unidirectionalUDLD (144)’ - unidirectional UDLD

(Uni Directional Link Detection) detected.

‘txRxLoopUDLD (145)’ - UDLD (Uni Directional

Link Detection) Tx Rx loop.

‘neighborMismatchUDLD (146)’ - UDLD

(Uni Directional Link Detection) neighbor mismatch.

‘authzPending (147)’ - authorization pending.

‘hotStdbyInBundle (148)’ - hot standby in bundle.

‘incompleteConfig (149)’ - all parameters on the port

have not been configured.

‘incompleteTunnelCfg (150)’ - incomplete tunnel config.

‘hwProgrammingFailed (151)’ - hardware programming failed.

‘tunnelDstUnreachable (152)’ - no route to

tunnel destination address.

‘suspendByMtu (153)’ - MTU allocation failed.

‘sfpInvalid (154)’ - SFP (Small Formfactor Pluggable)

is not Cisco certified.

‘sfpAbsent (155)’ - SFP (Small Formfactor

Pluggable) is absent.

‘portCapabilitiesUnknown (156)’ - the capabilities of the

port are unknown.

‘channelErrDisabled (157)’ - the port-channel to which

the port belongs is in error disabled state.

‘vrfMismatch (158)’ - Mismatch in source and transport VRF

(VPN Routing and Forwarding).

‘vrfForwardReferencing (159)’ - Forward referencing

transport VRF (VPN Routing and Forwarding).

‘dupTunnelConfigDetected (160)’ - two tunnel interfaces

with same configuration is not allowed.

‘primaryVLANDown (161)’ - primary VLAN is in down state.

‘vrfUnusable (162)’ - VRF (VPN Routing and Forwarding)

is unusable.

‘errDisableHandShkFailure (163)’ - port is not operational

due to an internal handshake failure.

‘errDisabledBPDUGuard (164)’ - BPDUGuard

(Bridge Protocol Data Unit) triggered

error disable on the port.

‘dot1xSecViolationErrDisabled (165)’ - error disabled

due to dot1x security violation.

‘emptyEchoUDLD (166)’ - UDLD (Uni Directional

Link Detection) empty echo.

‘vfTaggingCapErr (167)’ - VF Tagging capability

mismatch error.

‘portDisabled (168)’ - Port disabled.

‘tunnelModeNotConfigured (169)’ - Tunnel Mode is not

configured.

‘tunnelSrcNotConfigured (170)’ - Tunnel Source is not

configured.

‘tunnelDstNotConfigured (171)’ - Tunnel Destination

is not configured.

‘tunnelUnableToResolveSrcIP (172)’ - Unable to resolve

tunnel source IP address.

‘tunnelUnableToResolveDstIP (173)’ - Unable to resolve

tunnel destination IP address.

‘tunnelVrfDown (174)’ - Tunnel VRF down.

‘sifAdminDown (175)’ - SIF (Service Information Field)

is admin down.

‘phyIntfDown (176)’ - Physical interface is down.

‘ifSifLimitExceeded (177)’ - Interface SIF

(Service Information Field)limit is exceeded.

‘sifHoldDown (178)’ - SIF (Service Information Field)

hold down.

‘noFcoe (179)’ - No FCOE (Fibre Channel Over Ethernet)

configuration.

‘dcxCompatMismatch (180)’ - DCX Compatibility Mismatch.

‘isolateBundleLimitExceeded (181)’ - Isolation due to

bundle limit exceeded.

‘sifNotBound (182)’ - SIF (ervice Information Field)

is not bound.

‘errDisabledLacpMiscfg (183)’ - Error Disabled due to

LACP (Link Access Control Protocol) misconfig.

‘satFabricIfDown (184)’ - Satellite fabric interface down.

‘invalidSatFabricIf (185)’ - Invalid satellite fabric

interface.

‘noRemoteChassis (186)’ - No remote chassis.

‘vicEnableNotReceived (187)’ - VIC enable not received.

‘vicDisableReceived (188)’ - VIC disable received.

‘vlanVsanMappingNotEnabled (189)’ - VLAN VSAN mapping not

enabled.

‘stpNotFwdingInFcoeMappedVlan (190)’ - STP not forwarding

in FCOE Mapped Vlan.

‘moduleOffline (191)’ - Module Offline.

‘udldAggModeLinkFailure (192)’ - UDLD (Uni Directional Link

Detection) aggresive mode link failure.

‘stpInconsVpcPeerDisabled (193)’ - STP inconsistent

VPC (Virtual Port Channel) peer disabled.

‘setPortStateFailed (194)’ - Set port state failed.

‘suspendedByVpc (195)’ - Suspended by VPC

(Virtual Port Channel).

‘vpcCfgInProgress (196)’ - VPC (Virtual Port Channel)

configuration in progress.

‘vpcPeerLinkDown (197)’ - VPC (Virtual Port Channel)

peer link down.

‘vpcNoRspFromPeer (198)’ - VPC (Virtual Port Channel)

no response from peer.

‘protoPortSuspend (199)’ - Proto port suspend.

‘tunnelSrcDown (200)’ - Tunnel source down.

‘cdpInfoUnavailable (201)’ - CDP

(Cisco Discovery Protocol) information unavailable.

‘fexSfpInvalid (202)’ - FEX (Fabric Extender)

SFP (Small Formfactor Pluggable) invalid.

‘errDisabledIpConflict (203)’ - Error Disabled due to IP

conflict.

‘fcotClkRateMismatch (204)’ - FCOT CLK rate mismatch.

‘portGuardTrustSecViolation (205)’ - Error disabled due

to port guard (Cisco Trusted Security Violation).

‘sdpTimeout (206)’ - SDP (Secure Device Provisioning)

timeout.

‘satIncompatTopo (207)’ - Satellite incompatible topology.

‘waitForFlogi (208)’ - Wait for FLOGI.

‘satNotConfigured (209)’ - Satellite not configured.

‘npivNotEnabledInUpstream (210)’ - NPIV (N Port Identifier

Virtualization) not enabled in upstream.

‘vsanMismatchWithUpstreamSwPort (211)’ - VSAN

mismatch with upstream switch port.

‘portGuardBitErrRate (212)’ - Error disabled due to port

guard (Bit Error Rate).

‘portGuardSigLoss (213)’ - Error disabled due to

port guard (Signal Loss).

‘portGuardSyncLoss (214)’ - Error disabled due to port

guard (Sync Loss).

‘portGuardLinkReset (215)’ - Error disabled due to port

guard (Link Reset).

‘portGuardCreditLoss (216)’ - Error disabled due to port

guard (Credit Loss).

‘ipQosMgrPolicyAppFailure (217)’ - IP QOS Manager policy

application failure.

‘pauseRateLimitErrDisabled (218)’ - Port error disabled due

to pause rate limit condition.

‘lstGrpUplinkDown (219)’ - EthPM LSTGRP downstream link

down due to upstream link down.

‘stickyDnLinkFailure (220)’ - Port kept in error disabled

state due to Link Failure.

‘routerMacFailure (221)’ - Router MAC failure.

‘dcxMultipleMsapIds (222)’ - Port error disabled due to

multiple MSAP IDs (DCX).

‘dcxHundredPdusRcvdNoAck (223)’ - Hundred PDUs received

without ACK (DCX).

‘enmSatIncompatibleUplink (224)’ - Satellite Incompatible

Uplink.

‘enmLoopDetected (225)’ - Loop Detected (ENM).

‘nonStickyExternallyDisabled (226)’ - Disabled by VPD

Manager with shut/no shut allowed.

‘nonStickyExternallyDisabled (227)’ - Sub-group ID

not assigned.

‘vemUnlicensed (228)’ - VEM Unlicensed.

‘profileNotFound (229)’ - Profile not found.

‘nonExistentVlan (230)’ - VLAN does not exist.

‘vlanInvalidType (231)’ - Invalid VLAN type.

‘vlanDown (232)’ - VLAN down.

‘vpcPeerUpgrade (233)’ - VPC Peer Upgrade.

‘ipQosDcbxpCompatFailure (234)’ - IPQOS DCBXP compatibility

failure.

‘nonCiscoHbaVfTag (235)’ - Error Disabled due to Non-Cisco

HBA VF Tag.

‘domainIdConfigMismatch (236)’ - Domain ID config mismatch.

‘sfpSpeedMismatch (237)’ - SFP (Small Formfactor Pluggable)

speed mismatch.

‘xcvrInitializing (238)’ - Transceiver initializing.

‘xcvrAbsent (239)’ - Transceiver absent.

‘xcvrInvalid (240)’ - Transceiver invalid.

‘vfcBindingInvalid (241)’ - Invalid VFC Binding.

‘vlanNotFcoeEnabled (242)’ - VLAN down due to FCOE

disabled.

‘pvlanNativeVlanErr (243)’ - Private VLAN

Native VLAN error.

‘ethL2VlanDown (244)’ - Ethernet L2 VLAN down.

‘ethIntfInvalidBinding (245)’ - Invalid Binding

to Ethernet Interface.

‘pmonFailure (246)’ - PMON Failure.

‘l3NotReady (247)’ - L3 not ready.

‘speedMismatch (248)’ - Speed Mismatch.

‘flowControlMismatch (249)’ - Flow Control Mismatch.

‘vdcMode (250)’ - VDC mode

‘suspendedDueToMinLinks (251)’ - Suspended due

to Min Links.

‘enmPinFailLinkDown (252)’ - ENM Pin Fail Link Down.

‘inactiveM1PortFpathActiveVlan (253)’ - Inactive M1 Port

F Path Active VLAN.

‘parentPortDown (254)’ - Parent Port Down.

‘moduleRemoved (255)’ - Module Removed.

‘corePortMct (256)’ - Core Port MCT.

‘nonCorePortMct (257)’ - Non Core port MCT.

‘ficonInorderNotActive (258)’- FICON Inorder Not Active.

‘invalidEncapsulation (259)’ - Invalid Encapsulation.

‘modemLineDeasserted (260)’ - Modem line Deasserted.

‘ipSecHndshkInProgress (261)’ - IP Sec Handshake in

progress.

‘sfpEthCompliantErr (262)’ - Sfp Ethernet compliant error.

‘cellularModemUnattached (263)’ - Cellular Modem

unattached.

‘outOfGlblRxBuffers (264)’ - Out of Global Rx Buffers.

‘sfpFcCompliantErr (265)’ - Sfp Fc compliant Error.

‘ethIntfNotLicensed (266)’ - Ethernet Interface Not

Licensed.

‘domainIdsInvalid (267)’ - Domain IDs Invalid.

‘fabricNameInvalid (268)’ - Fabric Name Invalid.

other = 1
none = 2
hwFailure = 3
loopbackDiagFailure = 4
errorDisabled = 5
swFailure = 6
linkFailure = 7
offline = 8
nonParticipating = 9
initializing = 10
vsanInactive = 11
adminDown = 12
channelAdminDown = 13
channelOperSuspended = 14
channelConfigurationInProgress = 15
rcfInProgress = 16
elpFailureIsolation = 17
escFailureIsolation = 18
domainOverlapIsolation = 19
domainAddrAssignFailureIsolation = 20
domainOtherSideEportIsolation = 21
domainInvalidRcfReceived = 22
domainManagerDisabled = 23
zoneMergeFailureIsolation = 24
vsanMismatchIsolation = 25
parentDown = 26
srcPortNotBound = 27
interfaceRemoved = 28
fcotNotPresent = 29
fcotVendorNotSupported = 30
incompatibleAdminMode = 31
incompatibleAdminSpeed = 32
suspendedByMode = 33
suspendedBySpeed = 34
suspendedByWWN = 35
domainMaxReTxFailure = 36
eppFailure = 37
portVsanMismatchIsolation = 38
loopbackIsolation = 39
upgradeInProgress = 40
incompatibleAdminRxBbCredit = 41
incompatibleAdminRxBufferSize = 42
portChannelMembersDown = 43
zoneRemoteNoRespIsolation = 44
firstPortUpAsEport = 45
firstPortNotUp = 46
peerFCIPPortClosedConnection = 47
peerFCIPPortResetConnection = 48
fcipPortMaxReTx = 49
fcipPortKeepAliveTimerExpire = 50
fcipPortPersistTimerExpire = 51
fcipPortSrcLinkDown = 52
fcipPortSrcAdminDown = 53
fcipPortAdminCfgChange = 54
fcipSrcPortRemoved = 55
fcipSrcModuleNotOnline = 56
invalidConfig = 57
portBindFailure = 58
portFabricBindFailure = 59
noCommonVsanIsolation = 60
ficonVsanDown = 61
invalidAttachment = 62
portBlocked = 63
incomAdminRxBbCreditPerBuf = 64
tooManyInvalidFlogis = 65
deniedDueToPortBinding = 66
elpFailureRevMismatch = 67
elpFailureClassFParamErr = 68
elpFailureClassNParamErr = 69
elpFailureUnknownFlowCtlCode = 70
elpFailureInvalidFlowCtlParam = 71
elpFailureInvalidPortName = 72
elpFailureInvalidSwitchName = 73
elpFailureRatovEdtovMismatch = 74
elpFailureLoopbackDetected = 75
elpFailureInvalidTxBbCredit = 76
elpFailureInvalidPayloadSize = 77
bundleMisCfg = 78
bitErrRuntimeThreshExceeded = 79
linkFailLinkReset = 80
linkFailPortInitFail = 81
linkFailPortUnusable = 82
linkFailLossOfSignal = 83
linkFailLossOfSync = 84
linkFailNosRcvd = 85
linkFailOLSRcvd = 86
linkFailDebounceTimeout = 87
linkFailLrRcvd = 88
linkFailCreditLoss = 89
linkFailRxQOverflow = 90
linkFailTooManyInterrupts = 91
linkFailLipRcvdBb = 92
linkFailBbCreditLoss = 93
linkFailOpenPrimSignalTimeout = 94
linkFailOpenPrimSignalReturned = 95
linkFailLipF8Rcvd = 96
linkFailLineCardPortShutdown = 97
fcspAuthenfailure = 98
fcotChecksumError = 99
ohmsExtLoopbackTest = 100
invalidFabricBindExchange = 101
tovMismatch = 102
ficonNotEnabled = 103
ficonNoPortNumber = 104
ficonBeingEnabled = 105
ePortProhibited = 106
portGracefulShutdown = 107
trunkNotFullyActive = 108
fabricBindingSwitchWwnNotFound = 109
fabricBindingDomainInvalid = 110
fabricBindingDbMismatch = 111
fabricBindingNoRspFromPeer = 112
dpvmVsanSuspended = 113
dpvmVsanNotFound = 114
trackedPortDown = 115
ecSuspendedOnLoop = 116
isolateBundleMisCfg = 117
noPeerBundleSupport = 118
portBringupIsolation = 119
domainNotAllowedIsolated = 120
virtualIvrDomainOverlapIsolation = 121
outOfService = 122
portAuthFailed = 123
bundleStandby = 124
portConnectorTypeErr = 125
errorDisabledReInitLmtReached = 126
ficonDupPortNum = 127
localRcf = 128
twoSwitchesWithSameWWN = 129
invalidOtherSidePrincEFPReqRecd = 130
domainOther = 131
elpFailureAllZeroPeerWWNRcvd = 132
preferredPathIsolation = 133
fcRedirectIsolation = 134
portActLicenseNotAvailable = 135
sdmIsolation = 136
fcidAllocationFailed = 137
externallyDisabled = 138
unavailableNPVUpstreamPort = 139
unavailableNPVPrefUpstreamPort = 140
sfpReadError = 141
stickyDownOnLinkFailure = 142
tooManyLinkFlapsErr = 143
unidirectionalUDLD = 144
txRxLoopUDLD = 145
neighborMismatchUDLD = 146
authzPending = 147
hotStdbyInBundle = 148
incompleteConfig = 149
incompleteTunnelCfg = 150
hwProgrammingFailed = 151
tunnelDstUnreachable = 152
suspendByMtu = 153
sfpInvalid = 154
sfpAbsent = 155
portCapabilitiesUnknown = 156
channelErrDisabled = 157
vrfMismatch = 158
vrfForwardReferencing = 159
dupTunnelConfigDetected = 160
primaryVLANDown = 161
vrfUnusable = 162
errDisableHandShkFailure = 163
errDisabledBPDUGuard = 164
dot1xSecViolationErrDisabled = 165
emptyEchoUDLD = 166
vfTaggingCapErr = 167
portDisabled = 168
tunnelModeNotConfigured = 169
tunnelSrcNotConfigured = 170
tunnelDstNotConfigured = 171
tunnelUnableToResolveSrcIP = 172
tunnelUnableToResolveDstIP = 173
tunnelVrfDown = 174
sifAdminDown = 175
phyIntfDown = 176
ifSifLimitExceeded = 177
sifHoldDown = 178
noFcoe = 179
dcxCompatMismatch = 180
isolateBundleLimitExceeded = 181
sifNotBound = 182
errDisabledLacpMiscfg = 183
satFabricIfDown = 184
invalidSatFabricIf = 185
noRemoteChassis = 186
vicEnableNotReceived = 187
vicDisableReceived = 188
vlanVsanMappingNotEnabled = 189
stpNotFwdingInFcoeMappedVlan = 190
moduleOffline = 191
udldAggModeLinkFailure = 192
stpInconsVpcPeerDisabled = 193
setPortStateFailed = 194
suspendedByVpc = 195
vpcCfgInProgress = 196
vpcPeerLinkDown = 197
vpcNoRspFromPeer = 198
protoPortSuspend = 199
tunnelSrcDown = 200
cdpInfoUnavailable = 201
fexSfpInvalid = 202
errDisabledIpConflict = 203
fcotClkRateMismatch = 204
portGuardTrustSecViolation = 205
sdpTimeout = 206
satIncompatTopo = 207
waitForFlogi = 208
satNotConfigured = 209
npivNotEnabledInUpstream = 210
vsanMismatchWithUpstreamSwPort = 211
portGuardBitErrRate = 212
portGuardSigLoss = 213
portGuardSyncLoss = 214
portGuardLinkReset = 215
portGuardCreditLoss = 216
ipQosMgrPolicyAppFailure = 217
pauseRateLimitErrDisabled = 218
lstGrpUplinkDown = 219
stickyDnLinkFailure = 220
routerMacFailure = 221
dcxMultipleMsapIds = 222
dcxHundredPdusRcvdNoAck = 223
enmSatIncompatibleUplink = 224
enmLoopDetected = 225
nonStickyExternallyDisabled = 226
subGroupIdNotAssigned = 227
vemUnlicensed = 228
profileNotFound = 229
nonExistentVlan = 230
vlanInvalidType = 231
vlanDown = 232
vpcPeerUpgrade = 233
ipQosDcbxpCompatFailure = 234
nonCiscoHbaVfTag = 235
domainIdConfigMismatch = 236
sfpSpeedMismatch = 237
xcvrInitializing = 238
xcvrAbsent = 239
xcvrInvalid = 240
vfcBindingInvalid = 241
vlanNotFcoeEnabled = 242
pvlanNativeVlanErr = 243
ethL2VlanDown = 244
ethIntfInvalidBinding = 245
pmonFailure = 246
l3NotReady = 247
speedMismatch = 248
flowControlMismatch = 249
vdcMode = 250
suspendedDueToMinLinks = 251
enmPinFailLinkDown = 252
inactiveM1PortFpathActiveVlan = 253
parentPortDown = 254
moduleRemoved = 255
corePortMct = 256
nonCorePortMct = 257
ficonInorderNotActive = 258
invalidEncapsulation = 259
modemLineDeasserted = 260
ipSecHndshkInProgress = 261
sfpEthCompliantErr = 262
cellularModemUnattached = 263
outOfGlblRxBuffers = 264
sfpFcCompliantErr = 265
ethIntfNotLicensed = 266
domainIdsInvalid = 267
fabricNameInvalid = 268